Find research datasets worth reusing
Search datasets from major research repositories and use ShareScore to quickly assess how well each record supports discovery, access, and reuse.
44
datasets available to search
ShareScore release 0.9.0
Dataset results
44 results for “Expedition 366”
IODP Expedition 366 Alkalinity and pH
<p>Alkalinity was determined by Gran titration with an autotitrator (Metrohm 794 basic Titrino) using 0.1 M HCl at 20 degrees C. Report includes alkalinity, correction factor (if applicable), and pH.</p>
IODP Expedition 366 IW elemental analysis (ICP-solids)
<p>Elemental contents in hard rock and sediment samples was measured by inductively coupled plasma - atomic emission spectrocopy (ICP-AES). Data are presented by element-wavelength pair (e.g., more than one calcium line may be reported). Elemental lines for which data do not exist for a particular expedition will not appear.</p>
IODP Expedition 366 Bulk density (GRA)
<p>Gamma ray attenuation (GRA) data were acquired using a Cs-137 collimated source and a sodium iodide (thallium), or NaI(Tl), scintillation detector. The signal was calibrated using water and aluminum standards to provide a proxy for bulk density. This measurement was performed by a sensor mounted on either the Whole-Round Multisensor Logger (WRMSL) or the Special Task Multisensor Logger (STMSL); which track was used for a given data set is indicated in the data.</p>
IODP Expedition 366 Gas safety report
<p>This composite report returns data from two different gas chromatograph configurations (GC3 and NGA). Each row combines data from several measurements made on the same sample at the same time for a particular headspace or vacutainer sample. If data do not exist for a particular expedition, the column does not appear. Gas samples were measured by gas chromatography and either flame ionization detection (GC-FID) or thermal conductivity detection (GC-TCD). Reported analytes may include methane, ethane, ethene, propane, propene, n-butane, i-butane, n-pentane, i-pentane, n-hexane, i-hexane, n-heptane, i-heptane, nitrogen, oxygen, carbon monoxide, carbon dioxide, and hydrogen sulfide. When data are available, methane to (ethane + ethene) ratio is reported. To identify individual samples and tests, see each separate analysis (GC3, NGAFID, and/or NGATCD).</p>
IODP Expedition 366 Core summary
<p>Report includes detailed core data: drilling and coring depths, advancement, recovered core length measured on the catwalk and final curated length, core recovery, and sections cut.</p>
IODP Expedition 366 Visual core description
<p>Descriptions of samples, generally at the section half and smear slide or thin section scale, were performed by shipboard scientists and recorded in the JRSO description software. Descriptive data for both macroscopic and microscopic examination were collected in a Microscoft Excel workbook by hole. A zip file of the entire expedition's observations is also available.</p>
IODP Expedition 366 Core drilling summary
<p>Report includes detailed drilling data for each core: pump(s) used, mud pumped, strokes, shear pins/pressure, bit size/rotation, weight on bit, top drive torque, rate of penetration, core jams, winch and wirelines, core catcher/shoe and barrel, and whether core orientation, drillover, formation temperature, tracers, liners were used.</p>
IODP Expedition 366 Core composite images
<p>A digital composite image (PNG) is made for each core comprising core sections scanned using a line-scan camera. The composite layout is equivalent to traditional core table photos. Top left is top of core; color and meter rule references are included.</p>
IODP Expedition 366 Vane shear strength (AVS)
<p>Shear strength was measured on section halves using a GEISA automated vane shear (AVS) frame and device controller. The device is suitable for sediment not affected by cementation (i.e., saturated, clay-rich, soft sediment). Shear strength measurements should be considered only approximate, particularly because the influence of pore pressure changes during the undrained experiment cannot be estimated. Report includes vane shear strength at the sample's failure point, maximum torque angle, penetration direction, and rate of vane rotation.</p>
IODP Expedition 366 Ion chromatography
<p>Cation and anion concentration in interstitial water samples was measured by ion chromatography using a conductivity detector. Cation analytes include calcium, magnesium, potassium, and sodium. Anion analytes include chloride, sulfate, and bromide.</p>
IODP Expedition 366 Formation temperature
<p>Formation temperature was measured by the advanced piston corer temperature tool (APCT-3), Sediment Temperature Tool (SET), or sediment temperature pressure tool (SETP) and reduced to in situ temperature and (for SETP) pressure estimates. These data are compiled per instrument run and assigned to a core (the core cut with the APCT-3 cutting shoe or the core following the SET deployment).</p>
IODP Expedition 366 ICP-AES elemental analysis (interstitial water)
<p>Elemental concentration in interstitial water samples was measured by inductively coupled plasma - atomic emission spectroscopy (ICP-AES). Data are presented by element-wavelength pair (e.g., more than one calcium line may be reported). Elemental lines for which data do not exist for a particular expedition will not appear.</p>
IODP Expedition 366 Closeup images
<p>Close-up images taken by digital cameras as requested by the science party, typically when the section-half image is not sufficient. Close-up photographs of the areas of interest may be taken from whole-round sections, pieces, or section halves in sediments and rock.</p>
IODP Expedition 366 Natural gamma radiation
<p>Natural gamma radiation (NGR) data in the ~0.1 to 3.0 MeV range were measured using eight custom-designed sodium iodide (thallium) [NaI(Tl)] detectors arranged along the core measurement axis at 20 cm intervals. The NGR system uses layers of passive shielding (lead) and active shielding (plastic scintillators and coincidence electronics) to reduce the cosmic-ray signal for low-count analysis of sediment core sections and to obtain the maximum signal-to-noise ratio. Data are reported on a total counts per second basis and the raw spectral files are available as compressed files for later analysis.</p>
IODP Expedition 366 Magnetic susceptibility (section half)
<p>Magnetic susceptibility was measured on section halves on the Section Half Multisensor Logger (SHMSL) using a Bartington MS2 meter and either a MS2E or MS2K probe. Because all JRSO cores meet minimum size requirements for these two probes, MSPOINT data are corrected for volume and recorded in SI susceptibility units (x10<sup>-5</sup>).</p>
IODP Expedition 366 Magnetic susceptibility (whole round)
<p>Magnetic susceptibility was measured on whole-round sections (and rarely section halves) on the Whole-Round Multisensor Logger (WRMSL) and/or Special Task Multisensor Logger (STMSL) using a Bartington MS2 meter and a 90 mm or 80 mm MS2C loop. As volume of the sample is not controlled for this experiment, susceptibility units are recorded in instrument units and are not volume-corrected.</p>
IODP Expedition 366 Photomicrographs
<p>Microscopic images of discrete samples were acquired using stereo and upright light microscopes and captured on digital cameras. Image files were uploaded along with a brief description and a record of the microscopic and lighting conditions when the image was taken.</p>
IODP Expedition 366 Bulk and grain density (MAD)
<p>Moisture and density (MAD) data were acquired on ~10 mL sediment or rock samples by measuring three out of four material parameters: wet (saturated) mass, wet volume, dry mass, and/or dry volume after 24 h drying in a convection oven at 105 degrees C. From the moisture and volume measurements, the following phase relationships are calculated: wet and dry water content, wet bulk density, dry bulk density, grain density, porosity, and void ratio. The combination of measurements is defined by the submethod chosen: A, B, C, or D. Wet (A, B, or C) and dry (A, B, C, or D) mass is determined using motion-compensated balances. Wet volume is determined either by helium pycnometry (A) or by the sample's geometric dimensions using calipers (A or D). Dry volume (C or D) is measured by helium pycnometry. Submethods A and B are not recommended by IODP. Submethod C is suitable for saturated materials such as fine-grained sediments. Submethod D is suitable for unsaturated porous material such as certain limestones and basalts.</p>
IODP Expedition 366 Spectrophotometry
<p>Interstitial water constitutents were measured by UV-VIS spectrometry using colorimetric methods (e.g., ammonium, nitrate, nitrite, phosphate, silica, and sulfide) by an Agilent CARY 100 UV-VIS spectrophotometer.</p>
IODP Expedition 366 Color reflectance
<p>Color reflectance data were measured on section halves using an integration sphere and a UV-VIS spectrophotometer mounted on the Section Half Multisensor Logger (SHMSL). Spectral counts are recorded in the range of 380 to 700 nm, covering the visible spectrum, and binned in ~2 nm bins. Spectral data are reduced from spectra and recorded in tristimulus XYZ values, CieLAB L*a*b* values, and other units.</p>
ScienceDex guides
Understand access before you commit
These curated guides explain access requirements, typical timelines, costs, and reuse considerations for widely used research datasets.
Allen Brain Atlas
Allen Brain Atlas is an Allen Institute collection of brain map atlases, datasets, APIs, and analysis tools covering mouse, human, and non-human primate brain resources.
Annotated Behaviour and Observability Dataset (ABODe)
ABODe is a University of Edinburgh DataShare dataset for behavior classification in group-housed mice using home-cage video, identities, bounding boxes, ground-plate positions, and annotator labels.
DANDI Archive for NWB datasets
DANDI is a BRAIN Initiative archive for publishing and sharing neurophysiology data, including electrophysiology, optophysiology, and behavioral data packaged as NWB and related standards.
International Brain Laboratory public data
The International Brain Laboratory public data releases expose standardized mouse decision-making experiments, including Neuropixels recordings, widefield calcium imaging, behavior, and session metadata accessed through the ONE API.
OpenNeuro
OpenNeuro is a free, open platform for sharing neuroimaging datasets, with public search, dataset pages, and download paths for web, S3, DataLad, and the OpenNeuro CLI.