Find research datasets worth reusing
Search datasets from major research repositories and use ShareScore to quickly assess how well each record supports discovery, access, and reuse.
2
datasets available to search
ShareScore release 0.9.0
Dataset results
2 results for “FBGs”
Liquid Resin Infusion (LRI) manufacturing and Spring_In monitoring by FBGs, DCs and 3D CMM meassurements
<p>ELADINE project is aiming to implement a numerical tool that can reduce reoccurring costs of low-volume production in composite manufacturing of primary structural elements and thus reducing overall manufacturing effort and carbon emissions. A<strong> primary goal of this project is to eliminate tolerance non-compliancy in the manufactured structures caused by natural and unavoidable post-manufacturing distortions, typical for composite materials</strong>. These distortions might render otherwise qualitative components unusable due to their final geometry.</p> <p>Objectives of the Numerical model validation are:</p> <ul> <li>To understand the dominant factors which affects the spring-in phenomenon.</li> <li>To provide the simulation tool with the required values of the properties that influence on spring-in.</li> <li>To verify the simulation tool ability to predict spring-in for a variety of conditions.</li> <li>To develop a procedure of adapting and embedding sensors (dielectric and fiber optic) to obtain proper, useful and accurate signals of the manufacturing parameters (T, degree of cure, strain).</li> <li>To develop interpretation procedures of the signal/curves of sensors to obtain on-line process monitoring information.</li> </ul> <p>To obtain the data to feed and develop the numerical tool able to estimate the component distortions after its manufacturing, a combination of Fiber Optic Sensors (FOS) based on Fiber Bragg Grating (FBG) technology, Dielectric Curing sensors (DC) and 3D scanning were used to monitor the composite coupon manufacturing and the distortions the days after being demoulded. During the manufacturing process embedded FBGs and DC sensors were used to monitor the coupon temperature and strain distribution and resin curing evolution. After the manufacturing and the demolding, the distortions evolution were monitored by the embedded FBGs and by 3D CMM measurements.</p> <p><strong>In the ELADINE project, the distortion monitoring was made to two Out-of-Autoclave manufacturing technologies: liquid resin infusion (LRI) and oven cured pre-preg</strong>. For both material systems, slightly curved coupons and C-shaped coupons were the geometries selected as representative for the Skin and spars of the wing box. The Skin coupon was curved panel with a 1475 mm radius (with edge rise of 7,65 mm) that was thought to best replicate the wing profile geometry. The C-spar coupon geometry selected for the study was a non-tapered spar section with two different angle with radius of curvature of 5mm and 12mm. This geometry was chosen to simplify measuring and comparisons with wing demo. Furthermore, three different thickness are studied for the Skin coupons and two for the C-spar coupons which were selected from different zones along the wing. Moreover, a C-spar coupon with variable thickness was studied, as a simulation of the transition between zones with different thickness in the wing.</p> <p><strong>In this dataset, the data from the FBGs, DCs and 3D CMM meassurements for the LRI manufacturing process and spring_in distortions monitoring is included.</strong></p>
Pre-Preg (PP) Manufacturing and Spring-in monitoring through FBGs, DCs and 3D CMM measurements
<p>ELADINE project is aiming to implement a numerical tool that can reduce reoccurring costs of low-volume production in composite manufacturing of primary structural elements and thus reducing overall manufacturing effort and carbon emissions. A<strong> primary goal of this project is to eliminate tolerance non-compliancy in the manufactured structures caused by natural and unavoidable post-manufacturing distortions, typical for composite materials</strong>. These distortions might render otherwise qualitative components unusable due to their final geometry.</p> <p>Objectives of the Numerical model validation are:</p> <ul> <li>To understand the dominant factors which affects the spring-in phenomenon.</li> <li>To provide the simulation tool with the required values of the properties that influence on spring-in.</li> <li>To verify the simulation tool ability to predict spring-in for a variety of conditions.</li> <li>To develop a procedure of adapting and embedding sensors (dielectric and fiber optic) to obtain proper, useful and accurate signals of the manufacturing parameters (T, degree of cure, strain).</li> <li>To develop interpretation procedures of the signal/curves of sensors to obtain on-line process monitoring information.</li> </ul> <p>To obtain the data to feed and develop the numerical tool able to estimate the component distortions after its manufacturing, a combination of Fiber Optic Sensors (FOS) based on Fiber Bragg Grating (FBG) technology, Dielectric Curing sensors (DC) and 3D scanning were used to monitor the composite coupon manufacturing and the distortions the days after being demoulded. During the manufacturing process embedded FBGs and DC sensors were used to monitor the coupon temperature and strain distribution and resin curing evolution. After the manufacturing and the demolding, the distortions evolution were monitored by the embedded FBGs and by 3D CMM measurements.</p> <p><strong>In the ELADINE project, the distortion monitoring was made to two Out-of-Autoclave manufacturing technologies: liquid resin infusion and oven cured Pre-Preg (PP)</strong>. For both material systems, slightly curved coupons and C-shaped coupons were the geometries selected as representative for the Skin and spars of the wing box. The Skin coupon was curved panel with a 1475 mm radius (with edge rise of 7,65 mm) that was thought to best replicate the wing profile geometry. The C-spar coupon geometry selected for the study was a non-tapered spar section with two different angle with radius of curvature of 5mm and 12mm. This geometry was chosen to simplify measuring and comparisons with wing demo. Furthermore, three different thickness are studied for the Skin coupons and two for the C-spar coupons which were selected from different zones along the wing. Moreover, a C-spar coupon with variable thickness was studied, as a simulation of the transition between zones with different thickness in the wing.</p> <p><strong>In this dataset, the data obtained from the FBGs, DCs and 3D CMM meassurements during a PP manufacturing process and spring-in distortions monitoring can be found.</strong></p>
ScienceDex guides
Understand access before you commit
These curated guides explain access requirements, typical timelines, costs, and reuse considerations for widely used research datasets.
Allen Brain Atlas
Allen Brain Atlas is an Allen Institute collection of brain map atlases, datasets, APIs, and analysis tools covering mouse, human, and non-human primate brain resources.
Annotated Behaviour and Observability Dataset (ABODe)
ABODe is a University of Edinburgh DataShare dataset for behavior classification in group-housed mice using home-cage video, identities, bounding boxes, ground-plate positions, and annotator labels.
DANDI Archive for NWB datasets
DANDI is a BRAIN Initiative archive for publishing and sharing neurophysiology data, including electrophysiology, optophysiology, and behavioral data packaged as NWB and related standards.
International Brain Laboratory public data
The International Brain Laboratory public data releases expose standardized mouse decision-making experiments, including Neuropixels recordings, widefield calcium imaging, behavior, and session metadata accessed through the ONE API.
OpenNeuro
OpenNeuro is a free, open platform for sharing neuroimaging datasets, with public search, dataset pages, and download paths for web, S3, DataLad, and the OpenNeuro CLI.